-
S8212B PANDUIT 42U 800×1000 Floor Stand Cabinet with all Accessories
PANDUIT S8212B
42U 800×1000 Floor Stand Cabinet with all Accessories
DESCRIPTION
• Front Single Hinge Door and Split Perforated Rear Door with 69% Open Perforation
• Vertically Split Hinged Side Panels (if applicable)
• Vertical Blanking Panel
• 1 Set of PDU Brackets (SPDUBRK)
• Heavy-Duty Casters and Leveling Legs
• Ganging Brackets
• Rear Equipment Rails Accommodate Cable Management Fingers (Fingers Sold Separately)
• Fully Integral Bonded without the Use of Grounding Wires – Equipment Rails, Door and Side Panels
• Static Load Rating – 3000 lbs & Rolling Load Rating – 2500 lbs$ 1,600.91 -
Nexans Splice Closure WTC1.5 Watertight closure for Fibre optic Cables
Nexans Splice Closure WTC1.5 Watertight closure for Fibre optic Cables
DESCRIPTION
Sealing system:
Fully mechanical sealing system for reduced installation and re-entry time. The top shell, sealed with
a gasket, can be easily installed and removed without special tools or torque control. – Cable sealing devices based on a mechanical compression system: this allows re-using all components for future upgrade or re accessing to the enclosure The mechanical sealing system perfectly fits Cables Blowing technology.$ 571.76 -
NKFD1W12BUDLCZ PANDUIT 24port LC Duplex (48port) Patch Panel with Adaptor
NKFD1W12BUDLCZ PANDUIT
24port LC Duplex (48port) Patch Panel with Adaptor
DESCRIPTION
- Factoiy configured with 12 or 24 duplex LC adapters for fast and easy cabling and installation
- Slide-out drawer slides foiward a full 300mm for seivice access to all fiber terminations, connections, and/or splices
- Supports both field termination via pot-and-polish using Panduit NetKey connectors, or fusion splicing with appropriate slack storage and cable management provisions
- Trunk and interconnect cable entiy via PG11 glands, 5mm blown fiber glands, 20mm knock-outs, or 30mm rubber grommets
- Simple two-piece, all-metal body construction for easy and economical installation with no loose components to misplace; improved protection over plastic fiber drawers
- Dedicated silk-screened white labeling areas on drawer front for individual fiber adapters and overall enclosure labeling for proper channel identification and patch cord traceability
$ 238.23 -
NKFD1W12BUDLCZ PANDUIT 12port LC Duplex Patch panel with adaptor
NKFD1W12BUDLCZ PANDUIT
DESCRIPTION
Pre-loaded fiber drawers provide a pre-configured,ready-to-install system for managing fiber optic terminations. The pre-loaded enclosure is a two-piece design with a slide-out drawer for full access to all fiber terminations and easy installation. The fiber drawer has integral mounting brackets suitable for installation in any 19″ wide EIA 310/IEC60297 compatible rack or cabinet.
$ 238.23 -
PUNDUIT NUL6X04WH-HEG
PUNDUIT NUL6X04WH-HEG
Copper Cable, Cat 6A, 4-Pair, 23 AWG, U/UTP, LSZH (IEC60332-
1), EuroClass Dca-s2-d2-a1, White, Euro pallet, 305m/1000ft$ 233.88PUNDUIT NUL6X04WH-HEG
$ 233.88 -
PUNDUIT NUC6C04BU-CE
PUNDUIT NUC6C04BU-CE
Copper Cable, Cat 6, 4-PR, 24 AWG, UTP, CM, Blue, Euro Pallet, 1000ft/305m
$ 140.22PUNDUIT NUC6C04BU-CE
$ 140.22 -
N890.021 Nexans LANmark-OF Fusion Splice Heat Shrink Protection 45mm 100x
N890.021 Nexans
DESCRIPTION
LANmark OF-accessories to complete the splicing system with heat shrink protectors 100 pieces per bag
Lenght: 45mm Compatible with tight buffer or loose tube cables, i.e. 250 and 900 um coated fibres. Compatible with tight buffer and maxistrip pigtails Designed for LANmark-OF Splice Cassette Heat Shrink Protectors (N890.090 and
N890.095) The heat shrink splice protector consists of a metal rod surrounded by a shrinkable plastic. The splice is inserted into the shrinkable plastic. After heating the plastic is well fixed around the splice and the metal wire provides strength so that the splice is well protected.$ 137.70 -
N42i.101 Nexans DIN-Rail Outlets and Boxes
NEXANS
· For DIN-Rail mount (35mm)
· Data connection for the industry
· For up to 6 copper of fibre optic Snap-In connectors (not included)
· Splice trays as accessories
· For technical enclosures, Wireless Access Points, Industrial cabinets
· Snap-In connectors not included· Robust metal body, powder coated
· IP20 protection rating with individual dust shutters
Possibility of Individual port colour coding through coloured shutter
· up to 6 LANmark RJ45 or GG45 Snap-In jacks
· up to 6 SC Snap-In couplers (6 fibres)
· up to 3 SC duplex Snap-In couplers (6 fibres)
· up to 6 LC duplex Snap-In couplers (12 fibres)
·
· Mix of copper jacks and optic adapters possible
· Strain release through cable gland or tie wraps
· Removable (screws) side cover
Type of cables
· Shielded Industrial Category 6 and 7 data cables, AWG 24 to AWG23
· Fiber optic cables up to 15mm diameter
· Simplex – Duplex and breakout fibre optic cables
· Tight buffer or loose tube fibre optic cables
· Pre-terminated cables$ 127.69 -
N439.4SNB Nexans LANmark-OF Sliding Patch Panels
N439.4SNB Nexans
DESCRIPTION
Application
Accepting the range of ST couplers or LANmark-OF snap-ins, these patch panels with sliding mechanism facilitate front side installation.
Compatibility
Suitable for tight buffer cables (direct termination) , Loose tube cables using Splice Cassette / pigtailed terminations. Accepts pre-terminated cable assemblies.$ 78.96$ 83.04N439.4SNB Nexans LANmark-OF Sliding Patch Panels
$ 78.96$ 83.04 -
N521.661BK Nexans Patch Panel 24 Snap-In Fixed Black
N521.661BK Nexans
DESCRIPTION
Nexans Snap-In range of patch panels are designed to accomodate any of the Snap-In connectors in the LANmark product family (LANmark-7A, LANmark-7, LANmark-6A, LANmark-6, and LANmark-5). The Snap-In panels feature an exclusive Clip-On system to secure the connector in the panel and to provide a simple means of earthing shielded connectors to facilitate installation. Connection of the panel to earth is achieved with a unique Auto-Connect
feature removing the need for individual bonding conductors. The panels also have a series of complementary cable management products such as blank panels and patch cord guides.
The patch panels are designed for standard 19″ enclosures, are 1U high, and support the following common features:
– 24 Ports with shutters
– Designed for Screened and Unscreened Snap-In connectors
– Compatible with all performance categories of connector
– Clip-On mechanism for simple earthing
– Exclusive rear cable management facilities
– Robust construction
– Printed numbering for port labelling
This panel features vertical “T” clips for rapid cable retention which allows loading of the panel in around 25% of the time needed to fasten tie wraps which leads to time saving during installation.$ 31.04 -
N116.P1A200OK Nexans LANmark-6 Patch Cord Cat 6 Unscreened LSZH 20m Orange
N116.P1A200OK Nexans
DESCRIPTION
Application
LANmark-6 Patch Cords can be used to deliver a full end-to-end Class E solution. They provide improved data throughput and allow for the inclusion of a cross-connect or Consolidation Points for maximum system flexibility. They will also maximise the lifetime and long term performance of the system by minimising the risk of wear & tear damage which can be caused by using non-matched cords. LANmark-6 Cords feature a slim over-moulded boot which is kept inside the RJ45 boundaries to enable High Density Patching with 48 cords in 1 height unit. They also come with a Retrofit Latch Protector, which can be used for colour coding of different services.$ 27.23 -
WMPFSE Panduit 1U Cable Manager
Panduit WMPFSE
1U Cable Manager
DESCRIPTION
Horizontal cable managers shall be capable of managing
cables on the front and rear of any 19″ EIA rack. The
manager shall consist of a 1-piece construction that is
molded out of plastic. Horizontal managers shall have
pass through holes that incorporate integral bend radius
control as well as fingers with rounded edges. The
manager shall have rigid end fingers that incorporate
integral bend radius control. Hinged covers shall allow
access to the cable pathway without having to completely
remove the cover from the manager.$ 22.87WMPFSE Panduit 1U Cable Manager
$ 22.87
